Technics

Technics SL 1000R Reference Class Turntable

£15,999

Coreless Direct Drive Motor

The motor that forms the heart of the direct drive turntable is based on the coreless direct drive motor that was developed for the SL-1200G launched in 2016, and further improved. The double coil twin rotor-type coreless direct drive motor that was newly developed for this purpose had coils on both sides for 12-pole, 18-coil drive, with high enough torque to drive the heavyweight-class platter (approximately 7.9-kg). Offsetting the coils on both sides 60 degrees improved the rigidity of the substrate, suppressing fine vibrations and reducing self-inductance. These improvements achieved stable rotation of 0.015% wow and flutter or less, which is considered to be the measurement limit. Also, the thrust bearings supporting the heavyweight-class platter use a special engineering plastic to provide both high rigidity and reliability.


Suppressing Unwanted Motor Vibration

The motor that was developed for the SL-1200G served as the platform for the direct drive motor. The double coil, reinforced thrust bearings, and a chassis with increased rigidity achieved a stabilised motor with low centre of gravity. By positioning two stainless steel weights with high rigidity and high specific gravity at the bottom of the chassis, the rigidity and low centre of gravity are maintained. These thorough measures to prevent unwanted vibration help to achieve overwhelming rotary precision and improve S/N.


Heavyweight-class Turntable Platter

The turntable platter positions tungsten weights, which have an extremely high specific weight and are difficult to process, on the outer periphery of a 10-mm-thick brass weight. The brass weight is laminated onto the aluminium die-cast, giving the platter a total weight of approximately 7.9 kg and an inertial mass of approximately 1 ton・cm. A deadening rubber for eliminating unwanted vibration is also attached to the rear surface to form a 3-layer construction and achieve high rigidity and excellent vibration damping characteristics.


Separate Control Unit

The control unit is separated from the main unit to suppress the effects of unwanted noise on the main unit. In order to achieve a power supply circuit that provides good regulation for high torque, a switching power supply is used. To reduce the noise reaching the pickup, the switching power supply is equipped with a unique technology that provides a voltage supply with minimal noise by a newly developed "unwanted noise reduction circuit". Also, to minimise the noise even during communication, a highly reliable system that resists the effects of external noise is used for communication between the main unit and the control unit. These thorough noise-reduction measures achieve the world's highest-level S/N.


Minute Adjustment and Indication of Rotations

This turntable supports not only LP (33 1/3 rpm) and EP (45 rpm) analogue records, but also SP (78 rpm). Rotation (rpm) can also be set down to two decimal places (maximum ±16%) from the control unit. The OLED display is also capable of displaying rotation with accuracy down to two decimal places, so the user can both hear and see extremely precise rotation.


High-sensitivity Tonearm

To enable the tonearm to precisely track the record's rotation, Technics has traditionally used the static balance, S-type universal tonearm with a lightweight, high damping magnesium tonearm pipe. The gimbal suspension construction tonearm uses high-precision bearings. Highly skilled Japanese craftsmen handle all assembly and adjustment to achieve a high initial-motion sensitivity to precisely trace the grooves cut into the records. OFC is used for internal wiring, so the music signal relayed from the cartridge is not dampened and the musical energy cut into the record is not lost, thereby producing highly vivid sounds.


Tonearm Base

The tonearm base, to which the tonearm is mounted, is strongly integrated with the turntable part. Comparing the turntable base part with the tonearm mounting construction, the relationship of the tonearm bearings, turntable bearings, and needle position is always constant, providing a structure in which the vibration caused by the rigidity of the turntable base materials has minimal effect, and the tonearm performance is maximized. An optional tonearm base can also be purchased, enabling, in addition to the standard tonearm, an existing short or long-type tonearm from SME or Ortofon to be mounted (up to three including the standard tonearm).

High-quality Terminal

A gold-plated 5-Pin DIN terminal is used, enabling the user to select the desired PHONO cable. An integrated, machined, high-rigidity aluminum housing also suppresses external noise from reaching the pickup.


A Rigid Cabinet and High Damping Silicon Insulator

The cabinet has a 2-layer construction consisting of BMC (bulk molding compound) and a 30-mm-thick aluminium top panel. The turntable part is a 3-layer construction comprising BMC, aluminium die-cast, and a 25-mm-thick aluminium top panel. This gives the system a construction of 5 layers of different materials to ensure sufficient rigidity. The insulator that supports the cabinet is a special silicon rubber that combines high vibration damping characteristics and long-term reliability. Reinforcement with a cylindrical tube made of a microcell polymer absorbs vibrations in the horizontal direction. These parts are contained in a zinc die-cast housing with high specific gravity, for isolation from external vibrations.


SL-1000R
Direct Drive Turntable System


Turntable section

Drive Method
Direct Drive
Motor
Brushless DC motor
Turntable Speeds
33 1/3, 45, 78 rpm
Adjust Range
±16 %
Starting Torque
0.39 N・m / 4.0 kg・cm
Wow And Flutter
0.015 % W.R.M.S.
Turntable Platter
Brass and aluminium diecast combined
Diameter : 323 mm
Weight : Approx. 7.9 kg (including turntable mat)

Tonearm Section

Type
Universal Static Balance
Effective Length
From the tonearm pivot to the stylus : 254mm
From the tonearm pivot to the spindle : 239mm
Overhang
15 mm
Tracking Error Angle
Within 1° 48' (at the outer groove of 30 cm (12") record)
Within 0° 30' (at the inner groove of 30 cm (12") record)
Offset Angle
21°
Arm Height Adjustment Range
0 - 15 mm
Stylus Pressure Adjustment Range
0 - 4 g (Direct Reading)
Applicable Cartridge Weight Range (including Headshell)
15.9 - 19.7 g (without auxiliary weight)
18.8 - 23.6 g (with small auxiliary weight)
22.5 - 26.3 g (with middle auxiliary weight)
26.0 - 31.0 g (with large auxiliary weight)

Terminals

Audio Output
PHONO (Din Jack) x 1 *Straight Type Cable Only

General

Power Supply
AC 110 - 240 V, 50 / 60 Hz
Power Consumption
10 W
Approx. 0.05 W (Standby)
Dimensions (W x H x D)
Main Unit 531 x 188 x 399 mm
Control Unit 110 x 84 x 350 mm
Weight
Main Unit Approx. 40.2 kg
Control Unit Approx. 2.1 kg
Operating Temperature Range
0° to +40°
Operating Humidity Range
35 % to 80 % RH (no condensation)
Accessories
Turntable, Turntable mat, EP record adaptor, Balance weight, Auxiliary weight(Small)(Middle)(Large), Overhang gauge, Screw set for turntable, Detachable handle, Hex wrench, Insulator attachment, Dust cover, AC main leads, Owner's manual

We our in the process of updating our Doug Brady Hi Fi website, which now provides you with automatic real-time stock updates. We believe in an honest approach when displaying the availability of products. When viewing a product listing page, you'll see one of the following stock indicators. 

Stock Information : We have (current stock level number) in stock. 

In Stock - Order Now - Delivered free to you on [delivery-date] 

This item is brand new and guaranteed in stock from our shop stock.
Our shop stock will be dispatched on the date displayed on the product page, delivery will be booked for the delivery date displayed. We will send you a DPD tracking number where you will be given a 1 hour time slot on the day of delivery. 

 

In Stock - 2-3 day Dispatch - Delivered to you FREE by  [delivery-date] 

This item is brand new and in stock at our off site warehouse.
Stock being dispatched from our off site warehouse may take a day or two longer for you to receive. We may also dispatched directly from the manufacturer or distributor. This is often the case for particularly large or heavy items where specialized service is required. For anything which can take time to get to you, we'll contact you quickly.

 

Stock information : Please call ☎ - 01925 828009

Availably to order. Occasionally, due to stock demand, we can sell out. We either have this on order with stock due in or we do not usually have back up stock of this item in store. When you make a purchase, we will inform you quickly when the item is due in from the manufacturer and deliver as soon as it arrives with us. Usually this is only a short wait of 3 - 5 days, we will contact you with a estimated delivery time.

Sold Out

This item is currently sold out with the supplier or manufacturer please call us so we can give you an estimated time. 01925 828009 

In Stock - Free Next Day Delivery*

Free next working day delivery when you spend over £50. We will send you a tracking number where DPD will give a one hour delivery window. Services available Monday to Friday (excluding public holidays) to most mainland UK addresses for in stock items ordered before our cut-off time at 3pm. Terms apply.

Free Saturday delivery when you spend over £500. We will send you a tracking number where DPD will give a one hour delivery window. Services available to most mainland UK addresses for in stock items ordered before our cut-off time on Friday 3pm. Terms apply.

* Excludes CLICK & COLLECT items  Some of our manufactures request for there items not to be sold on line for these items our delivery service may not be available in curtain locations so please call to order 01925 828009

Christmas and New Year Deliveries - (subject to stock availability)

Our last order cut-off time for delivery before Christmas is 12pm on Thursday 23rd December, which will be delivered on Friday 24th December.

Our last order cut-off time for delivery before New Year is 12pm on Thursday 30th December, which will be delivered on Friday 31st December.

Order Date (before the 12pm cut-off time for same day dispatch) Expected Delivery Date
Monday 20th December Tuesday 22nd December
Tuesday 21st December Wednesday 23rd December
Wednesday 22nd December Thursday 24th December
Thursday 23rd December Friday 30th December
Friday 24th December to Tuesday 29th December Wednesday 29th December
Wednesday 29th December Thursday 30th December
Thursday 30th December Friday 31st December
Friday 31st January to Monday 3rd January Wednesday 5th January☨
Normal delivery service resumes from then on.

 

Delivery Costs

Standard next day delivery is free for all orders to most UK mainland addresses. All other delivery prices are determined by the destination, the service chosen and the value and weight of your order. Addresses in the Scottish Highlands, offshore, Northern Ireland & Ireland may incur additional delivery costs, depending on the items ordered. Prices are calculated at the checkout for all services and destinations.

You may also like

Recently viewed